Metra Electronics Automobile Accessories 95 9012 User Manual

INSTALLATION INSTRUCTIONS FOR PART 95-9012  
APPLICATIONS  
•GOLF 1999-2006  
•GTI 1999-2005  
•JETTA 1999-2005  
(Excluding NEW JETTA 2005)  
•PASSAT 2000-2005  
95-9012  
KIT FEATURES  
• Double DIN Head Unit Provision  
• Stacked ISO DIN Head Unit Provision  
KIT COMPONENTS  
A) Radio Housing • B) (8) Phillips screws  
B
A
WIRING AND ANTENNA CONNECTIONS (Sold Separately)  
• 70-1784 VW harness 1998-2001  
• XSVI-9003-NAV VW Interface 2003-up  
Antenna adapter:  
• 40-EU55-adapter for amplified antenna 2002-up  
• 40-VW53 adapter for amplified antenna 1998-01  
TOOLS REQUIRED:  
• Small Flat Blade Screwdriver • Panel Removal Tool  
• 86-9001 Radio Removal Tools (2 sets)  
1-800-221-0932  
© COPYRIGHT 2009 METRA ELECTRONICS CORPORATION  
 
95-9012 DASH DISASSEMBLY  
GOLF 1999-2006 GTI 1999-2005  
JETTA 1999-2005  
(Excluding NEW JETTA 2005)  
PASSAT 2000-2005  
A
Disconnect the negative battery  
terminal to prevent an accidental  
short circuit.  
1
2
Insert the long ends of the 86-9001  
into the slots on the factory radio and  
pull out to remove. Note: Flat edge  
of key should point outward.  
(Figure A)  
3
For single DIN radios with the pocket,  
remove the radio and pocket, then  
pull out on the plastic tray separating  
the dash cavity. (Figure B)  
B
Continue to kit assembly.  
Note: This installation kit is an extremely tight fit and requires force to be  
“snapped” into the dash opening. Removal of aftermarket radio is even  
more difficult than installation, so please be sure to fully test the after-  
market radio prior to completing the kit’s installation.  
1
 
95-9012 KIT ASSEMBLY/ FINAL ASSEMBLY  
DOUBLE DIN HEAD UNIT PROVISION/  
ISO STACKED HEAD UNIT PROVISION  
A
1
2
Slide the DDIN radio unit into the  
DDIN bracket/radio housing assembly  
and secure the unit to the kit using  
the (8) Phillips screws supplied with  
the kit. (Figure A)  
Locate the factory wiring harness in  
the dash. Metra recommends using  
the proper mating adapter from Metra  
or AXXESS. Re-connect the negative  
battery terminal and test the unit for  
proper operation.  
3
Snap kit/ radio assembly into the  
dash opening.  
Note: This installation kit is an extremely tight fit and requires force to be  
“snapped” into the dash opening. Removal of aftermarket radio is even  
more difficult than installation, so please be sure to fully test the after-  
market radio prior to completing the kit’s installation.  
1-800-221-0932  
REV. 09-02-09 © COPYRIGHT 2009 METRA ELECTRONICS CORPORATION INST95-9012  
2
 

Leica Laser Level 772787 User Manual
Lenovo Computer Monitor D221 User Manual
Life Fitness Exercise Bike 95R 0XXX 01 User Manual
LifeSource Blood Pressure Monitor UA 789 User Manual
Lowrance electronic GPS Receiver GlobalMap 5000C User Manual
Magnavox Portable CD Player AZ7461 User Manual
Makita Grinder 9047L User Manual
Maxtor Server STM310005CAD00G RK User Manual
Maytag Dishwasher KUDS24SEAL2 User Manual
MGE UPS Systems Power Supply EX 11RT User Manual