Metra Electronics Automobile Accessories 99 8227S User Manual

INSTALLATION INSTRUCTIONS FOR PART 99-8227S  
APPLICATIONS  
TOYOTA 4 RUNNER  
2010  
99-8227S  
KIT FEATURES  
DIN Head unit provisions with pocket  
ISO DIN Head unit provision with pocket  
DDIN Head unit provision  
ISO Stacked Head unit provision  
Painted matte silver to match factory dash  
KIT COMPONENTS  
• A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) DDIN Brackets  
• E) DDIN Trim Plate • F) Pocket • G) (4) PC-7503 Panel Clips • H) (2) Phillips Screws  
A
B
H
D
E
C
F
Wiring & Antenna Connections (Sold Separately)  
• TYTO -01 Toyota Interface 2006-UP  
•70-1761 Toyota Harness  
G
TOOLS REQUIRED  
• Phillips Screwdriver • Panel Removal Tool • Small Flat Blade Screwdriver  
• Small Socket Set  
METRA. THE WORLD’S BEST KITS.™  
1-800-221-0932  
metraonline.com  
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION  
 
99-8227S DASH DISASSEMBLY  
TOYOTA 4 RUNNER 2010  
1
Unclip and remove the (2) climate  
control knob trim panels. (Fig. A)  
A
Unclip and remove the climate  
control. (Fig. B)  
2
3 Remove (4) 10 MM bolts securing  
the radio. (Fig. C)  
B
C
Continued on Pg. 2 .............  
1
 
99-8227S DASH DISASSEMBLY  
TOYOTA 4 RUNNER 2010  
4 Unclip and remove the vents from  
D
E
F
the factory radio panel. (Fig. D)  
Remove the (2) Phillips screws  
securing the trim panel on the top of  
the factory radio panel. (Fig. E)  
5
6
7
Remove the (4) Phillips screws  
securing the outer a/c vent control  
wheel trim pieces. (Fig. F)  
Unclip and remove the hazard  
switch from the factory radio trim  
panel. (Fig. G)  
G
2
 
99-8227S KIT PREPARATION  
TOYOTA 4 RUNNER 2010  
1
Attach the outer a/c vent control  
A
wheel trim pieces to the radio  
housing using the factory hardware.  
(Fig. A)  
Attach the trim panel to the top of  
the radio housing using the factory  
hardware. (Fig. B)  
2
Note: 2 screws are provided “Justin” case.  
B
Attach the a/c vents to the radio  
housing. (Fig. C)  
3
4
5
Snap the hazard switch into the  
radio housing. (Fig. D)  
Attach (4) panel clips to the radio  
housing. (Fig. D)  
C
D
3
 
99-8227S KIT ASSEMBLY  
TOYOTA 4 RUNNER 2010  
DIN HEAD UNIT PROVISION  
1
Locate the factory wiring harness in  
A
the dash. Metra recommends using  
the proper mating adapter from  
Metra or AXXESS. Re-connect the  
negative battery terminal and test  
the unit for proper operation.  
Slide the DIN cage into the Radio  
Housing and secure by bending the  
metal locking tabs down. (Fig. A)  
2
B
3 Snap the pocket into the bottom  
opening of the radio housing.  
(Fig. B)  
4 Slide the aftermarket head unit into  
the cage and secure. (Fig. C)  
Reassemble dash in reverse order  
of disassembly.  
5
C
4
 
99-8227S KIT ASSEMBLY  
TOYOTA 4 RUNNER 2010  
ISO DIN HEAD UNIT PROVISION  
1
Locate the factory wiring harness in  
the dash. Metra recommends using  
the proper mating adapter from  
Metra or AXXESS. Re-connect the  
negative battery terminal and test  
the unit for proper operation.  
A
Mount the ISO Brackets to the head  
unit with the screws supplied with  
the unit. (Fig. A)  
2
B
3 Snap the pocket into the bottom  
opening of the radio housing.  
(Fig. B)  
Slide the head unit into the radio  
opening until the side clips engage.  
(Fig. C)  
4
5 Snap the Trim plate into the Radio  
Housing. (Fig. C)  
C
6 Reassemble dash in reverse order  
of disassembly.  
5
 
99-8227S KIT ASSEMBLY  
TOYOTA 4 RUNNER 2010  
DOUBLE DIN HEAD UNIT PROVISION  
1
Locate the factory wiring harness in  
the dash. Metra recommends using  
the proper mating adapter from  
Metra or AXXESS. Re-connect the  
negative battery terminal and test  
the unit for proper operation.  
A
Cut and remove the center bar from  
the radio housing. (Fig. A)  
2
3 Snap the Double DIN brackets to the  
inside edge of the Double DIN trim  
plate. (Fig. B)  
B
Slide the Double DIN head unit or  
stacked ISO head units into the  
bracket/radio housing assembly and  
secure the Double DIN head unit  
or stacked ISO head units to the  
assembly using the screws supplied  
with the radio. (Fig. C)  
4
C
Snap the double DIN trim plate into  
the radio housing. (Fig. C)  
5
6 Reassemble dash in reverse order  
of disassembly.  
6
 
NOTES  
 
NOTES  
 
NOTES  
 
INSTALLATION INSTRUCTIONS FOR PART 99-8227S  
METRA. THE WORLD’S BEST KITS.™  
1-800-221-0932  
metraonline.com  
© COPYRIGHT 2004-2010 METRA ELECTRONICS CORPORATION  
 

Learning Resources Baby Toy LER 2996 User Manual
LG Electronics Telephone LIP 8000 User Manual
Lincoln Electric Welder SVM155 A User Manual
Loewe DVD Player ViewVision DR+ User Manual
Lowrance electronic Stud Sensor EP 15 User Manual
Lumens Technology Scanner PS750 User Manual
Makita Saw 5277NB User Manual
McCulloch Lawn Mower 165H107RB BA165H107RBC User Manual
McIntosh Stereo Amplifier MCC602TM User Manual
Meyer Sound Car Speaker UPA 1p User Manual